A card case is a simple and stylish way to keep your keys and other valuables safe, when you’re out and about.
Here’s how to make one for your wallet.
Get a template and a pencil.
Here are some ideas: 1.
Make your own template.
The easiest way to make a card-case wallet template is to download a template from here, and then draw on it with a pencil or pencil-point.
The template is the size of a half-size photo.
For example, if you’re making a 12″ x 18″ card case, you’ll want to make it 4″ wide x 6″ high.
Get the template for your card case.
Here, I used a template that looked like this: template1 template2 template3 template4 3.
Cut a piece of card-paper.
Cut out a piece about the size and shape of a dime, and fold the edges down.
You should end up with something like this.
This is the template you want.
I used some tape to hold the card-papers together.
The card-cases you get from craft stores or online often have a very thin card-board inside, so cutting out a thin piece of paper to make your own is easier.
Fold the edges of the card case down.
I did this by folding the edges over.
I found that the cards folded together pretty easily.
Once they’re folded, fold them again over the card, to make sure they’re all the same size.
Fold them in half again, to get the desired card-fold shape.
Cut your card-cover paper.
Cut some card-covers from the template.
Make sure they have the right thickness and the right length to match your card cases.
Cut them into strips about the same width as the template, about the length of the template itself.
(Remember that card-screws are not very sturdy, so it’s best to use them with care.)
Cut the strips into 1″ x 3″ strips about 1/8″ thick.
Fold each strip into the template again, making sure that the top of the strips match up with the template’s top.
Fold a piece from the card cases template, using your scissors to cut the strips of card paper into a 3″ x 6.5″ rectangle.
Fold it over the top strip, creating a triangle.
The triangle should be about the width of the top half of the templates card-drawing surface.
Cut the triangles from the 3″x6.5 template, as shown in the picture below.
The triangles should fit the template perfectly.
Fold one of the triangles over the template and fold it over itself, making a rectangle.
You can fold it even further.
Fold both sides of the rectangle into one.
Fold in the triangle you made in step 7.
Make a triangle from the top corner of the triangle.
Fold up one of its sides, and make sure it’s the same thickness as the top edge of the other side.
Fold over the triangle, creating another rectangle.
This time, fold it in half.
Cut and cut some additional triangles.
Using scissors, cut out triangles of about the thickness you want your cards to be, as long as they don’t go through your card backs.
If you want them to fit over the cards and keep your cardcases from sliding around, make sure you cut the triangles a little larger than the templates width.
Draw a circle on the template as shown below.
Make the shape you want, and cut a piece that’s about the right size to hold your card.
Draw your circle on a piece your card holder has on it, and draw a line along the top and bottom.
Cut one of your circles in half, so you can easily draw your other half.
Fold your cards down to make the triangles, and press them in place.
Press the cards together tightly, as seen in the pictures below.
Cut two cards from the templates sides and fold them over into triangles.
Fold triangles in half and fold over the other triangle, so they’re the same height as your cardfold sides.
Fold all the triangles together.
Draw an arrow on the templates side.
Use a ruler to draw a circle along the inside of the cards template.
Cut an arrow from the other template, so that the arrow points to your card holders side.
The arrow should be exactly the same diameter as your template’s template-drawer surface.
The arrows will go through the cardfold, and they will sit right on top of your cards.
Cut three of your triangles in halves, as in the diagram below.
Cut four triangles from both templates sides, as the picture shows.
Cut each triangle in half so that it’s about 1″ long.
Cut it into triangles as in step 14. Cut all of